Decayed joist end beneath an old house floor

Wet Rot vs Dry Rot: How to Tell Them Apart

October 30, 2026•12 min read

Wet rot and dry rot are both fungal decay in timber, but they behave very differently. Wet rot needs persistently damp wood and usually stays close to the leak. Dry rot can survive at lower moisture levels and can travel across other surfaces, even into masonry, which is why it is treated as the more serious of the two. Neither can be diagnosed reliably from a photograph or a quick look, so if you suspect either, the sensible next step is an inspection by a qualified surveyor or specialist.

Altura Surveyors

Understand Timber Decay Before You Act

Altura Surveyors provides residential property surveys that identify significant defects and potential risks, with clear reports and repair recommendations.

Book a property survey

TL;DR

  • Wet rot is a group of decay fungi that need very damp timber and usually stay near the source of water. Dry rot is one specific fungus, Serpula lacrymans, and it can spread through a building.

  • Both depend on moisture. “Dry” rot is a misleading name: with no moisture it cannot progress.

  • Look for cuboidal cracking, cotton-wool-like growth and red dust (dry rot) versus soft, spongy or bleached timber (wet rot).

  • Fixing the moisture source matters more than the label. Treatment without that fix will not last.

  • A survey is a visual, non-invasive inspection. It can flag signs of rot and recommend further investigation, but it cannot see inside walls or under fixed floors.

Table of Contents

What is the difference between wet rot and dry rot?

The SPAB’s guidance on timber-decaying fungi describes wet rot as a group of white or brown rots caused by various fungi, most commonly Coniophora puteana. Dry rot is a single brown rot, caused by Serpula lacrymans. It thrives at lower moisture levels than wet rot and can cross non-timber surfaces and penetrate masonry.

In practice that gives you three differences that matter:

  1. Moisture needed. Wet rot wants wood that stays properly wet. Dry rot can establish in timber that is damp but not soaked.

  2. Spread. Wet rot tends to stay where the water is. Dry rot can move beyond the original damp area.

  3. Risk to the building. Dry rot is described by SPAB as the most aggressive wood-destroying fungus, so it usually calls for a wider investigation.

The moisture levels behind each type

The New Forest National Park Authority gives true dry rot a timber moisture range of 20% to 30%, with around 95% relative humidity. Wet rot has an optimum of 50% to 60%. Other published guides quote slightly different bands, so treat the figures as a guide to the relative difference, not a threshold you can test for yourself with a cheap meter.

Moisture ranges compared for wet and dry rot

The key point is that both need water. SPAB notes that dry rot cannot progress when no moisture is present, although spores may stay dormant. A leak that was repaired years ago may be the start of the story, not the end of it.

How to tell wet rot from dry rot

Appearance helps, but it is not proof. Several signs overlap, and rot is often hidden behind plaster, boards or floor coverings.

Sign

Dry rot

Wet rot

Timber surface

Darkens and cracks into cube-like blocks

White rot: bleached and fibrous. Brown rot: darker, often with cracking

Feel

Brittle and crumbly when dry

Soft or spongy, often obviously damp

Fungal growth

Grey-white cotton-wool-like sheets, later reddish fruiting bodies

Often little visible growth; sometimes dark-brown strands

Dust

Fine reddish spore dust

Not typical

Smell

Musty

Musty or mushroom-like

Surroundings

Can show on adjacent plaster or brickwork

Usually confined to the wet area

The descriptions come from the SPAB and from the Building Conservation Centre’s timber guidance, which lists soft or spongy timber, warping and a mushroom-like odour for wet rot, and cotton-wool-like growth, reddish fruiting bodies, fine reddish dust and light-brown right-angled cracking for dry rot.

One caution: do not poke around a suspect area with the aim of confirming it yourself. Disturbing dry rot can release spores and can make a later assessment harder. Note what you can see, photograph it, and have it looked at.

Brown rot and white rot: how they fit in

You may see “brown rot” and “white rot” used in surveys and specialist reports. These describe the type of decay, not a separate problem.

  • Brown rot darkens the timber and mainly affects softwood. Dry rot is a brown rot.

  • White rot bleaches the timber and leaves it stringy or fibrous. It mainly affects hardwood.

According to SPAB, wet rot can be either a brown or a white rot, depending on the fungus involved. So “brown rot vs white rot” is a different question from “wet rot vs dry rot”: one is about how the wood looks and breaks down, the other is about which fungi and conditions are involved.

Where each one tends to appear

Wet rot commonly affects exposed timber such as external joinery: window frames, fascias, door thresholds. It also turns up wherever a leak keeps wood wet, for example around a failed shower tray or under a leaking pipe. The Property Care Association says wet rot is typically confined to the damp area because its mycelium does not spread into walls, though it can sometimes grow over masonry.

Dry rot prefers dark, still, unventilated spaces: beneath suspended floors, behind panelling, in roof voids or at the ends of joists built into damp walls. This is why it is often found late.

Why older homes are more exposed

Period properties in towns such as Farnham, Winchester and Wokingham often have suspended timber floors, built-in joist ends, lime plaster and original joinery. These are perfectly sound when kept dry and ventilated. They become vulnerable when a gutter fails, airbricks are blocked, or modern impermeable finishes trap moisture. If you are buying an older or altered home, a RICS Level 3 Building Survey is the more suitable inspection, because it looks in more depth at the construction and at the likely causes of any damp.

What causes rot in the first place

No moisture, no rot. The Building Conservation Centre notes that decay needs three things together: moisture, a food source (timber) and fungal spores. Spores are everywhere, and timber is the building material, so moisture is the factor you can control.

The Property Care Association’s guidance lists these among the usual causes:

  • Plumbing leaks and defective toilet plumbing

  • Condensation

  • Flood water trapped in under-floor voids

  • Impermeable floor coverings over timber

  • Inadequate sub-floor ventilation

Defective roofs and blocked gutters feature in both the New Forest and Building Conservation Centre guidance. The same defect that starts wet rot can also start dry rot.

Ventilation checks you can do yourself

The PCA says sub-floor ventilation should be kept up with suitable airbricks at roughly 1.8 m spacing, and that blocked vents and dead-air pockets should be cleared or corrected. From outside you can check that airbricks are not buried under soil, paving or a raised flower bed, and that gutters and downpipes are not overflowing onto walls. These are simple observations, not a diagnosis.

Airbrick partly obscured by raised ground

Is wet rot worse than dry rot?

Not necessarily. Dry rot is the more aggressive fungus and the more likely to spread, so it is usually the bigger worry. But wet rot is far more common: the New Forest National Park Authority reports it is responsible for up to 90% of wood decay in buildings.

Both can weaken timber. The Property Care Association says fungal decay can cause timber to darken, crack in cubes or bleach, and eventually lose strength. In a floor joist, rafter or lintel bearing, that can become a structural matter, and a structural engineer or specialist should then advise. A surveyor will not give a definitive structural opinion from a visual inspection and will say when one is needed.

Does wet rot stop once the timber dries?

Wet rot generally needs the wood to stay wet, so removing the water source is the first step. The PCA says the first response is a careful inspection to find how water is entering, then repairing the defect and preventing further water entry.

RICS guidance on moisture in traditional buildings takes a similar line. It recommends a holistic diagnosis that addresses causes rather than symptoms, dealing first with obvious defects such as ventilation and ground levels, allowing time for monitoring and natural drying, then reassessing before further treatment. It adds that recommendations should be proportionate to the defect and the building’s significance. You can read it in RICS guidance on investigating moisture.

Dry rot is different in one respect: because it can spread beyond the original damp patch and may be hidden, drying out the visible area is not enough. A specialist should establish how far it extends.

Repair decisions and getting the right help

Good outcomes depend on matching the response to the actual problem: fix the water, replace or repair only what is affected, and avoid over-treatment. For property managers and landlords weighing up repair routes, this article on preventing disrepair claims through maintenance covers the maintenance side of the same decision.

Commercial buildings

Rot is not only a residential issue. Flat roofs, rooflight upstands, rainwater goods and basement stores in commercial premises can all keep timber wet for years. A commercial building survey records visible defects and likely moisture sources, which helps with purchase decisions, lease negotiations and planned maintenance budgets.

Party wall situations

If you are planning a loft conversion, extension or basement works next to a neighbour, timber in a shared wall or at joist bearings may be affected by the works or may already be decayed. Where works fall under the Party Wall etc. Act 1996, a record of the condition beforehand is valuable. Our party wall surveying service covers notices, awards and condition schedules.

What a survey can and cannot tell you

A RICS survey is a visual, non-invasive inspection. We look at accessible areas, use a moisture meter where appropriate, and report what we can reasonably see. We do not lift fixed floorboards, cut into plaster or open up concealed voids. That means a survey can:

  • Flag signs consistent with rot, such as cracked or soft timber, staining, musty smells or high readings

  • Identify likely moisture sources such as defective gutters, roof coverings, blocked airbricks or leaking pipework

  • Recommend further investigation by a timber and damp specialist where needed

It cannot confirm which fungus is present or how far hidden decay extends. That takes opening-up work, which RICS guidance says may need the building owner’s permission.

If you have a particular concern, such as a stained skirting or a bouncy floor, a specific defect survey focuses on that issue. To understand how findings are rated in a report, see how to read your building survey report, and if a report raises concerns, read what to do after a bad building survey.

Which survey suits your situation

Altura Surveyors is independent and survey-only, with no estate agency ties and no repair work to sell. We cover Hampshire, Berkshire and Surrey.

  • Level 2 Home Survey suits conventional, more modern homes in reasonable condition. Our published price range is £480 to £635.

  • Level 3 Building Survey suits period, listed, altered or higher-value homes, where hidden timber problems are more likely. See what a Level 3 survey includes.

  • Pre-sale survey helps sellers find issues, such as a damp-affected window frame, before a buyer’s surveyor does.

  • Drone roof inspection looks at roofs, chimneys and gutters that are hard to reach, which are common sources of water entry.

Altura Surveyors

Reports are written in plain English and delivered within 5 working days. You can start with a free quote request or look at our Level 2 Home Survey.

FAQ

How do you know if you have wet rot?

Typical signs are soft, spongy or discoloured timber, warping, a musty or mushroom-like smell and persistent dampness nearby. Visible fungal growth is often absent. Because other problems can look similar, have a surveyor or timber specialist confirm it.

Is dry rot more serious than wet rot?

Usually, yes, because dry rot can spread across other surfaces and into masonry, so it is harder to contain. Wet rot is more common and usually stays near the water source. Both need the moisture problem fixed.

Will wet rot spread once it is dry?

Wet rot generally needs persistently damp timber, so it tends to stop spreading when the water source is fixed and the wood dries. Damaged timber may still need repair or replacement, and a specialist should check that the cause has really been dealt with.

Will insurance cover wet rot?

Policies vary, and many exclude gradual damage such as rot caused by long-term leaks or poor maintenance. Check your policy wording and speak to your insurer or broker before arranging work.

Can a survey find dry rot?

A survey can identify visible signs and likely causes, then recommend specialist investigation. Because it is non-invasive, it cannot confirm hidden decay inside walls or under fixed floors.

Book your survey

If you are buying, selling or managing a property with possible damp or timber decay, we can inspect it and explain what we find in plain English. Contact Altura Surveyors to book.

Sources

A

Altura Surveyors

Ask About Suspected Timber Rot

Contact Altura Surveyors to discuss a property survey that can flag signs of rot and recommend further investigation where needed.

[email protected]

Email us

+44 1252 929125+44 7412 316284

Recommended

This article is general information only and is not a substitute for a survey or professional advice on a specific property. For advice on your property, contact Altura Surveyors.

blog author avatar

Altura Surveyors

Independent RICS-regulated building surveyors specialising in older, altered and higher-value homes across Hampshire, Berkshire and Surrey.

Back to Blog